| Subject | Text |
| SCMI---Great Test & Measurement Software for free downlo | website: http://www.virtins.com
PC version: http://www.virtins.com/SCMISetup.exe
Pocket PC Versio |
| measurement | once the caps are charged you should be reading the resistance of the resistors. |
|
|
| HITACHI PROBLEM | HELLO, Both of these gentalmen are right, however don't forget the H.O.T this transistor is a comm |
| I think the standby power supply is a simple type of SMPS with a few watts of output?
If you have |
| Service manual for SHIMADZU model: EB-3200H | Hello,
I'm working on a SHIMADZU electronic weighing balance model EB-3200H. The display cannot be |
| AGAIN: What about the real-world? Does pin #2 (center pin) of EACH Regulator go to ground "foil |
| Sell Instruments | Miko-Kings Instruments Ltd http://www.miko.com.hk
Miko-Kings Instruments Ltd., hereinafter called |
| Panasonic TC-P65S1 - begins power up, then shuts off | Make: Panasonic
Model: TC-P65S1
Description: 65" Plasma, Manf. Jan-2010
The TV did not |
| between B-E it should be short and vice versa,and +on the base and - on the colector should read OL, |
| I think the most likely problem is the backup battery on the CPU board, it may leak and cause corros |
| Instead of a jumper, use your meter set to AC amps. What do you measure when you turn the unit on?
|
| Electrical Feedback | What are these "amps" you are throwing up as being measured by the cable company? AS expressed, none |
| [quote:b360352202="JP in Wisconsin"]Thanks for the tip.
If I put a voltmeter on those leads, wh |
| Ati FIre gl Graphics Card broken inductor needs repair | Hi
i have an ati fire gl v7100 graphics card and one of the inductors has come away from its b |
| Advantages of FADOS7F1 | Advantages:
Output voltage degree of multimeters are very low. FADOS7F1 has various voltage deg |
| Hellige manual/help | Hi,
I have an Hellige ECG-machine, which stopped functioning adequately. It's a Hellige EK53. Pro |
| okay here are the readings from the power print, does not look good.
incoming power is 50 V AC on |
|
|
| If you need current feedback to get a correct waveform through an inductive load, please take a look |
| I have said that HOT is good because i tried to replaced it by D2499 and tried the other one D1555 b |
| Thanks all for the amazing information on this thread - I was able to resurrect my beloved IL-60 sub |
| Need help on a Plasma Grundig planatron pw 110-520/9 | Folks,
Issue is a very famous fault on this Plasma: Picture disappears and screen stays black, afte |
| Regulators Pin 2s are grounds, all three regulators reads 00.2ohms respect to ground point.
1) Re |
| Service Manual Kenwood VT-165 2 Ch AC voltmeter | Hi, I am new to here.
I have brought a second hand subject meter and found the two channels is no |
| same problem on the TV sasung CW29M064N | i did not see or hear anything from this TV samsung CW29M64N
switched on , it reset down after & |
| the measurement is from centre pin to each outer pin - conducts 1 way only- but the only real test i |
| Re: Blown Fuse - Troubleshoot Why | [quote:5c2ee5ef36="huntro1"]Hi Vtech,
Thanks for your reply. I will get the amp measurement this w |
| Blown Fuse - Troubleshoot Why | Hi Vtech,
Thanks for your reply. I will get the amp measurement this weekend and post it here. I |
| don't ya just hate that when you are trying to fix one thing, something else craps out.
Sounds li |
| Troubleshooting Tips (ref. Figure 3-3)
NOTE: Follow previously discussed “IC6501 Startup Sequence”. |
| Remember;
When talking about "impedance", it is actually the resistance of the speaker |